New 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch Board

New 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch BoardNew 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch Board
Move your mouse over image or click to enlarge
New 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch Board New 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch Board New 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch Board

New 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch Board

$15. 31
Qty:
OR
Product Description

Details

Note: The color of the item may vary slightly due to photography and your own computer
Self-locking type: Output data to achieve the trigger flip state.Each self-locking independent of each other.For example: Press A button, A Relay Work. Press A button again, A Relay Off.
12V remote control switches,it is recommended over 500mA DC power supply.
Application: for anti-theft alarm, remote control electric windows, signal control, industrial control, lifting equipment, Electrical control circuit, etc.
Parameters:
Operating Voltage: 12V
Working frequency: 315MHZ
Control Channel: 2 Channel
Contact capacity: ≤ 10A/250VAC; 10A/30VDC
Work status: Jog/Self-locking/Interlock
Supporting remote control: 50 ~ 100m (Open Place) two-button remote control
Encoding type: Learning code
Module size: 73 x 52 x 25mm/2.87 x 2.04 x 0.98 inch
Weight: 82g
Remote operate battery:23A 12V L1028(not include)
Note: due to the battery is embargoed in the air transport, so the battery is not include in the package, thanks for your understanding.


Factory Default Mode: Jog/Momentary Mode
Three Working Modes: Jog/Momentary Mode, Self-lock Mode, Interlocked Mode

Operation Way and Steps:
Each transmitter and receiver have been finished linking and factory default mode has been set up. When you receive them, you do not need to link again, you just need to connect the wiring according to our wiring diagram layout.

About three modes:
Jog/Momentary Mode:
Press and hold the button A, the Receiver A (Relay A)turns on,
Release the button A, the Receiver A (Relay A) turns off.
Self- lock Mode:
Press the button A, the Receiver A (Relay A) turns on,
Press the button A again, the Receiver A (Relay A) turns off.
Interlocked Mode:
Press the button A, the Receiver A (Relay A) turns on,
Press the button B, the Receiver B (Relay B) turns on, the Receiver A (Relay A) turns off.

If you want to change the factory default mode, below is the method:
1. Clear:
Press and hold the learning button on the receiver board, the red light (Signal Light) will turn on and stay on for about 5 seconds, till the red light turns off, then release the learning button. It means clearing succeed, previous mode will not work after clearing successfully.
2. Choose the Working Mode:
Press and hold the learning button on the receiver, the red light will turn on and stay on for about 5 seconds, then turn off (Clearing Steps), do not release, still hold the learning button, and then the red light will begin to flash, it will flash once, then twice, and finally three times.
(1).After the light flashes ONCE, release the learning button, it becomes
Interlocked Mode.
(2).After the light flashes TWICE, release the learning button, it becomes Self- lock Mode.
(3).After the light flashes THREE times, release the learning button, it becomes Jog/Momentary Mode.
3. Link the remote control:
(After the Working Mode is chosen, you can start to link the remote control according to the mode you choose)
Press the learning button on the receiver until the red light turn on, and then release the learning button, the red light will stay on. Press the button on the transmitter you want to link, and the red light (Signal Light) on the receiver board will flash twice, at this time, it means that the transmitter and receiver finish linking. Then you can press the button on the transmitter, the related receiver will work as the mode you choose.
Note:
1.When the receive has Single channel, you can only learn one button, just learn and link the button which you want to control.
2. When the receiver has Two channels, you need to press the first button, then the second button, it means link successfully.
3. When the receiver has More Than Two channels, such as four, six, eight, twelve, sixteen or more channels, if you link one button successfully, the other buttons on the transmitter will link automatically.

Attention:
The receivers in our store are mainly used together with the related transmitter in our company. If you want to use your own transmitter, please confirm if the operating frequency, chip type and vibration resistance of your transmitter are in accordance with ours. If not, they will fail to be linked to.

Package includes:
1x 2CH Receiver Board
1x 2CH Remote Controller
Additional Information

Additional Information

Name New 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch Board
Free Shipping Yes
Brand BQLZR
UPC No
EAN No
Size 2.17x1.57x0.79
Color Black
Weight (kg) 0.08
Reviews

Be the first to review this product

Write Your Own Review

You're reviewing: New 3 In 1 12V 2 Channel Wireless Remote Controller Control Switch Board

How do you rate this product? *

 
1 1 star
2 2 star
3 3 star
4 4 star
5 5 star
Value
Quality
Price